Name Part III Refer to the drawing (167E100) on the next page and answer the following questions, 1. Name the unit shown

Business, Finance, Economics, Accounting, Operations Management, Computer Science, Electrical Engineering, Mechanical Engineering, Civil Engineering, Chemical Engineering, Algebra, Precalculus, Statistics and Probabilty, Advanced Math, Physics, Chemistry, Biology, Nursing, Psychology, Certifications, Tests, Prep, and more.
Post Reply
answerhappygod
Site Admin
Posts: 899603
Joined: Mon Aug 02, 2021 8:13 am

Name Part III Refer to the drawing (167E100) on the next page and answer the following questions, 1. Name the unit shown

Post by answerhappygod »

Name Part Iii Refer To The Drawing 167e100 On The Next Page And Answer The Following Questions 1 Name The Unit Shown 1
Name Part Iii Refer To The Drawing 167e100 On The Next Page And Answer The Following Questions 1 Name The Unit Shown 1 (43.87 KiB) Viewed 36 times
Name Part Iii Refer To The Drawing 167e100 On The Next Page And Answer The Following Questions 1 Name The Unit Shown 2
Name Part Iii Refer To The Drawing 167e100 On The Next Page And Answer The Following Questions 1 Name The Unit Shown 2 (53.93 KiB) Viewed 36 times
Name Part III Refer to the drawing (167E100) on the next page and answer the following questions, 1. Name the unit shown on the drawing. 2 Where is the drawing number located? 3. The scale of the drawing is 4. What is the next assembly? 5. How many individual parts make up the com- pleted unit? 6. Name the bed length of the unit shown. 7. What information is given on the slot welds? & What are the special instructions indicated in Note "A"? 9. The distance from the base of the unit to the top of the rails is Unit 17 Plug and Slot Welds 237 10. What special instructions are to be followed when welding the rails into place? A B. 11. How many different types of welds are indicated? 12. The total width of the unit is 13. The width of the mounting plates is 14. What instructions are given concerning the hole positions on the mounting plate? 15. Welding Note "B" is concerned with
Copyright Goodhean Will EL A 63 O BED TIE PLATE 167W1008 -SURFACE GRIND HossCooREGS Ø MOUNTING PLATE 167 WIOOF -BE SURE 7/8 HOLE IS IN POSITION IN PLACE AS SHOWN WHEN WELDING PLATE SURFACE GRIND (TYP) 101- BED TIE PLATE STICOA SREGD WELDING NOTE "B" 3 RSW TO BE MADE ON VERTICALE OF EACH BED TIE PLATE AS SHOWN IN FRONT APRON 067W100G) AND REAR APRON (67100) 16TWIDOC-5 TUBULAR CONNECTOR SURFACE GRIND 5 AND 6 FOOT BEDS ARE OBTAINED DRAWING SHOWS 4 FOOT BED BY ADONG 12 INCH SECTIONS $0 e MOUNTING PLATE- 16TWOOE PAR LM- Chexo RONOTERM NEXT ASSEM. 167E103 FAPRON TWOOD V64 1/2" WOGA bom - PERTANT-WEEP WELDS MAY FROM THESE CONS TE PLATES WHEN WELDING ALS TO WELD RALS WITH GROUND EDGES ON THE NOGE ENCLOSING THE 2500/250 KEEP WELDS FROM EDGES OF TE PLATES AT 4 MINU AS SHOWN ON END VIEW ABOVE SECTION AA RAPPON NETWOOK JOHNSON MACHINERY CO ASSEMBLY LATKE P NETURCIC 67100 238 Wing Pine Reading
Join a community of subject matter experts. Register for FREE to view solutions, replies, and use search function. Request answer by replying!
Top
Post Reply

Return to “Archived Questions & Answers”