Detail 5.1.63 ID 1 2 3 4 5 6 7 8 9 10 11 12 13 2 3 4 5 6 7 8 9 Component 813 [2-81- Interior Film¹ Gypsum Board Ecotouch

[answerhappygod]

Detail 5 1 63 Id 1 2 3 4 5 6 7 8 9 10 11 12 13 2 3 4 5 6 7 8 9 Component 813 2 81 Interior Film Gypsum Board Ecotouch 1 (401.36 KiB) Viewed 54 times

Detail 5.1.63 ID 1 2 3 4 5 6 7 8 9 10 11 12 13 2 3 4 5 6 7 8 9 Component 813 [2-81- Interior Film¹ Gypsum Board Ecotouch Pink Fiberglass Batt 6" x 1 5/8" Steel Studs Exterior Sheathing Thermafiber RainBarrier 45 Mineral Wool Semi Rigid Insulation Heckmann Pos-l-Tie Masonry Tie 16" (406) o.c. Vented Air Cavity² Brick Veneer Zinc Barrel Exterior and Interior Insulated 6" x 1 5/8" Steel Stud (16" o.c.) Wall Assembly with Heckmann Pos-l-Tie Veneer Anchoring System Supporting Brick Veneer and Owens Corning R-20 Batt Insulation in Stud Cavity - Clear Wall Rubber Washer (EPDM) Galvanized Steel Wire Pintle Exterior Film¹ 406 [1-4"] Thickness Inches (mm) 1/2" (13) 6" (152) 18 Gauge 5/8" (16) Varies Varies 1.5" (38) 3 5/8" (92) 1/16" (1.59) 3/16" (5) Ø Conductivity Btu-in / ft².hr.°F (W/m K) 1.1 (0.16) 0.30 (0.043) 430 (62) 1.1 (0.16) 0.24 (0.034) 5.4 (0.78) 726 (105) 1.7 (0.25) 645 (93) 813 [2¹-8"] 16" (406 [1-4"] Nominal Resistance hr-ft².°F/Btu (m²K/W) R-0.7 (0.12 RSI) R-0.5 (0.08 RSI) R-20 (3.5 RSI) R-0.6 (0.10 RSI) R-6.3 to R-21.0 (1.11 to 3.70 RSI) R-0.4 (0.07 RSI) R-0.2 (0.03 RSI) Anchor Detail Density lb/ft³ (kg/m³3) 50 (800) 0.55 (8.8) 489 (7830) 50 (800) 4.5 (72) 0.075 (1.2) 120 (1920) 412 (6600) 62 (997) 489 (7830) 10 11 12 Specific Heat Btu/lb.°F (J/kg K) 0.26 (1090) 0.17 (710) 0.12 (500) 0.26 (1090) 0.29 (1220) 0.24 (1000) 0.19 (720) 0.12 (500)
Detail 5.1.63 Exterior Insulation 1D R-Value (RSI) R-6.3 (1.11) R-8.4 (1.48) R-12.6 (2.22) R-16.8 (2.96) R-21.0 (3.70) Exterior and Interior Insulated 6” x 1 5/8" Steel Stud (16" o.c.) Wall Assembly with Heckmann Pos-l-Tie Veneer Anchoring System Supporting Brick Veneer and Owens Corning R-20 Batt Insulation in Stud Cavity-Clear Wall R₁D ft²-hr-°F / Btu (m² K/W) R-29.7 (5.23) R-31.8 (5.60) R-36.0 (6.34) R-40.2 (7.08) R-44.4 (7.82) R₂ ft².hr.°F / Btu (m² K/W) 1.00 R-17.1 (3.02) R-18.6 (3.28) R-21.3 (3.75) R-23.7 (4.17) R-26.3 (4.62) 0.90 0.90 0.70- 0.60 View from Interior View from Exterior Nominal (1D) vs. Assembly Performance Indicators 0.50 0.40 0.30 0.20 0.10 0.co Thermal Performance Indicators Assembly 1D (Nominal) R-Value Transmittance/ Resistance without Anomaly U。 Btu/ft² .hr .°F (W/m²K) 0.058 (0.33) 0.054 (0.31) 0.047 (0.27) R₁D 0.042 (0.24) 0.038 (0.22) U。. Ro 'Assumptions and limitations for surface temperatures identified in ASHRAE 1365-RP R-23.4 (4.12 RSI) + exterior insulation "clear wall" U- and R-value
Consider the design of a new building. The wall type shown above will be used. (If the image is unclear, click here to open it in a new tab.) The thickness of the "mineral wool" exterior insulation (layer '6') is to be determined. This type of insulation has rated thermal resistance R-4.2 per inch ( hr. ft² °F/btu. If the design intent is to achieve a clearfield thermal resistance R-17, what thickness of mineral wool insulation is needed? O 0.5 inches 1 inch 1.5 inches 2 inches 3 inches 4 inches 5 inches