- Notes On The Lab The Primary Routing Prefix For This Organization Is 2001 Abcd Aaaa 64 The Organization Has Multiple S 1 (67.25 KiB) Viewed 57 times
- Notes On The Lab The Primary Routing Prefix For This Organization Is 2001 Abcd Aaaa 64 The Organization Has Multiple S 2 (73.82 KiB) Viewed 57 times
- Notes On The Lab The Primary Routing Prefix For This Organization Is 2001 Abcd Aaaa 64 The Organization Has Multiple S 3 (49.41 KiB) Viewed 57 times
- Notes On The Lab The Primary Routing Prefix For This Organization Is 2001 Abcd Aaaa 64 The Organization Has Multiple S 4 (70.11 KiB) Viewed 57 times
of the successful pings for questions 6 and 9! Thank
you!
Notes on the lab The primary routing prefix for this organization is 2001
aaaa::/64 The organization has multiple sites, each of which are setup as a subnet. The challenge of this lab is to get the connections online for all sites and all sites communicating with each other. Tip: You may want consider using the 2811 router as opposed to the ISR 4321 routers. 1. Setup the following topology within Packet Tracer - PC-PT PCS 2960-ATT Switch IPV6 Prefix 2001:ABCD:AAAA:: - Server-PT Server 2 PC-PT PC4 2960-24TT Switchi FF 2960-24TT Switch 4 F 1984321 Routero PC-PT ISR/32 Router1 PC7 E B 2960-24TT Switch2 PC-PT PC3 D с 2960-2411 Switch PC-PT PCI 760-24 Switch 2960-24TT Switch3 PC-PT PCO Server-PT Server Server-PT Server1 PC-PT PC2 Note: You may need to add additional modules to the routers and switches to connect the devices. Completed a 2. We will first configure Router 0 with the following commands. We will start by enabling unicast routing for IPv6 and then configure the serial port on the router with an IPv6 address. Router>enable Router#config t Enter configuration commands, one per line. End with CNTL/2. Router (config)#ipv6 unicast-routing Router (config)# interface s 0/1/0 Router (config-if)#ipv6 enable Router (config-if)#ipv6 address 2001: abcd: aaaa:ff::1/64 Router (config-if)#no shutdown LINK-5-CHANGED: Interface Serial0/170, changed state to down Router (config-if)#1 We have now configured one side of the serial link between the routers Completed 3. Configure Router 1 to get the link up between the two routers. Make sure you can ping between the two routers, troubleshoot if necessary. Completed 4. Now configure each of the subnets attached to both routers using the subnets as labeled on the topology (similarly in how you configured the serial ports on the routers). Completed 0 5. Using the auto-config method, get the PCs and servers connected to their appropriate networks. Completed D
6 Given what we have configured so far, you should now be able to ping the networks on their respective routers. For example, based on our original topology, PC 2 on Subnet D should be able to ping PC 5 on Subnet G. Troubleshoot if required. Insert an image of the successful ping between PC 2 and PC 5 below. 7. If you attempt to ping Server 2 from PC 5 what happens? Why? What are 2 different methods (do not say tunnelling) that we could use to make communication happen?
8. We now enable the unicast routing protocol “RIP” that we introduced in the earlier networking course on both routers to get the routers to advertise their respective networks. We will first create the RIPng process/group named "Elephant" and then enable RIPng on each router interface as shown in the configuration below. You will need to specify the correct interfaces on your routers. Router (config)#ipv6 router rip elephant Router (config-rtr) #exit Router (config)#interface gigabitethernet 0/0 Router (config-if)#ipvé rip elephant enable Router (config-if)#exit Router (config)# Remember, you will need repeat this command "ipv6 rip elephant enable' on each router interface on both routers Completed 9. Now you should have connectivity and routing for every host on each network. Now attempt to ping Server 2 from PC 5...... it should work, If not, troubleshoot. Insert an image of the successful ping between Server 2 and PC 5 below. 1