Apparatus setup The sketch of PASCO 850 interface is given in the "Introduction" of this lab manual. 1. Connect the phot

[answerhappygod]

Apparatus Setup The Sketch Of Pasco 850 Interface Is Given In The Introduction Of This Lab Manual 1 Connect The Phot 1 (49.35 KiB) Viewed 225 times

Apparatus Setup The Sketch Of Pasco 850 Interface Is Given In The Introduction Of This Lab Manual 1 Connect The Phot 2 (21.56 KiB) Viewed 225 times

Apparatus Setup The Sketch Of Pasco 850 Interface Is Given In The Introduction Of This Lab Manual 1 Connect The Phot 3 (50.28 KiB) Viewed 225 times

Apparatus setup The sketch of PASCO 850 interface is given in the "Introduction" of this lab manual. 1. Connect the photogate 1 to Port 1 and the photogate 2 to Port 2 of the Digital Inputs on 850 Interface respectively (Fig. 2). 2. Measure the mass m and the diameter d of the steel ball. Record the data in Table 1. = 3. Stick a Velcro pad to a steel ball and measure its dimension d, - d+the thickness of one Velcro pad. Record the data in Table 1. 4. Stick a Velcro pad to each of two balls and stick them together, then measure the dimension of the 2- ball system d, -2d+ thickness of two Velcro pads. Record the data in Table 1. 5. Unscrew and pull out the guide bar outward until the center of the ball #1 at position A is just touch the mark h₂ on the guide bar as shown in Fig. 2. 6. Measure and record h, and h₂ accurately using a 15 cm ruler and record h=h₂ -h, in Table 1. Table 1 Data of the balls' mass, dimension and position. m (kg) d (m) d, (m) d₂ (m) 0.130350-03137 0.0345 0.067 h, (m) h₂ (m) 0.06410-12M h=h₂ h₁ (m) 0.056 130-35 Software setup.
Experiment & Colision elastic collision Time in Gate L 1 2 3 . S 6 Mean Shd. Dev H 160 60 00245 00253 0.0254 00258 00240 00255 1.97730 ela colision) Time In Gate 2 Ch 2 5) 0.0258 00262 00262 00265 00265 0.0261 38300 - Y slastic Time in Gate 1 CHI (1) 0.0751 00256 0.0254 00260 60240 Estop 1044200 Time in Gate 2, Cha M 86061 There 0.0344 PRUE SOME 2004 LOIMIIFLE I HAK Time in L CHI 00 00252 ESTOO 00117 $320 4001 2025) 14010 3 Time in Gate 2 CH2 N Tro 10000 MO SHO 9.026 30264 1421210 nett Time in Gate 1 Ch I 1100 0.0004 WHOS MEDS cases BOHA $100 EXAMPLE Timen Gate 1 Ch 10 NITH 83434 6114 01043 BIZTO 01204 0.013 Tine Gate 1 EN 1 10 dans SHOD MED 032 04004 va -DIPURET CH Teat tha THE Inte 6000 HILTO 83100 ANTO C DIM 650/200+ H The CONL M FOTO ONE 0.0044 5:004) 0.0045 INDO +DOGTE THUND 012 AND IN ATTS WILL BELA BOM 0535
total Work to be done: 1. Print Graph Page #1(similar to Fig. 3) 2. Click "Print" icon in the Tool Bar, select # of pages to be printed, click "print" at the bottom. Let your TA check your Graph Page #1. If it is OK, your TA will sign it Caution: Make sure that your pristed Page #1 is OK before you close the Capstone. All the data collected in Experiment 6 will be lost when the Capstone is closed 3. Close PASCO Capstone by clicking the red-cross at the upper corner, then select "discard" 4. Turn off PASCO 850 interface and shut down the computer. 5. Clean up your bench. Data analysis 1. Calculate <>ie, the average value of the three mean values in columns 1, 3 and 5 in Table on Graph Page #1. Record the calculated data in Table 2. 2 Calculate <>, Le, the average value of the three mean values in columns 2, 4 and 6 in Table on Graph Page #1. Record the calculated data in Table 2 3. Calculate <>, Le, the average value of the three mean values in columns 7,9 and 11 in Table on Graph Page #1. Record the calculated data in Table 2. 4. Calculate <>.Le, the average value of the three mean values in columns 8, 10 and 12 in Table on Graph Page #1. Record the calculated data in Table 2. Table 2 Measured average time of balls) passing the photogates <> (8) <> (5) > (1) 0.0/+31 <> (1) C-1126 00220 5. Use data in Tables 1 and 2 as well as Eqs. (4) and (7) to calculate the speed(s) of the ball(s) before and after elastic/inclastic collision. Record the results in Table 3. Table 3 Measured speed(s) of the ball(s) before and after clastic/inclastic collision o (m²) (m/s) (m/s) (m/s) 17231 0.326 6. Use Eqs. (1), (2), (6), and the data in Tables 1 and 3 to calculate the quantities listed in Tables 4 to 8. Table 4 Total energy of ball #1 in Measurement #1 (clastic collision) total energy of ball #1 at % total energy of ball #1 just before collision () Is the total energy conserved? difference position A ( yes Table 5 Momentum conservation in Measurement #1 (elastic collision) momentum after % Is the momentum conserved? momentum before collision (Ag m/s) L collision (bg m/s) difference 0 Ball #1 2.691 yes Ball #2 1-504 60