Complete the table only Required is to fill the Table I1 I2 I3 I4 Before Delay After Delay Q1 Q2 Q1 Q2 0 0 0 0 0 0 0 1 0
Posted: Fri Apr 29, 2022 9:15 am
Complete the table only
Required is to fill the Table
I1
I2
I3
I4
Before Delay
After Delay
Q1
Q2
Q1
Q2
0
0
0
0
0
0
0
1
0
0
1
0
0
0
1
1
0
1
0
0
0
1
0
1
0
1
1
0
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
1
0
1
1
1
1
0
0
1
1
0
1
1
1
1
0
1
1
1
1
PLC Automatic Door Control System • System have 2 motion detectors (11,12) O The door will open when one of the sensors detect motion. O • System have 2 outputs(Q1,Q2) One responsible for opening the door ,the other for closing door. And gates will be needed to build a standard interlocking circuit (B2,B3):by this way only one output can be active at time. . 2-detecors: 13:kimit switch open and 14 limit switch close: o the final position of the door are detected by the limit switches 13 and 14 (NC contact) 0 when the door is open 13 limit switch changes the state from close to open. o when the door is close 14 limit switch changes the state from close to open • we will add a off-delay block; when the detectors area of the 2 motion detectors is free for min time the door will close again. OBJECT DETECTIVE SENSOR DOOR OPEN DOOR OPEN OPEN LIMIT SWITCH CLOSE LIMIT SWITCH OPEN LIMIT SWITCH
Infrared sensor o Door Opening limit switch Closing limit sw Opening limit switch List of inputs/outputs List of inputs ·motion detectors: 11, 12 Closing limit switch: I. Opening limit switch: Iz List of outputs -Opening motor : Q Closing motor :- Q2 MDO 11 LSO 13 B001 R B002/2 B003 B004 Remont 10:00+ B002 MDI LSC 8001M
- Complete The Table Only Required Is To Fill The Table I1 I2 I3 I4 Before Delay After Delay Q1 Q2 Q1 Q2 0 0 0 0 0 0 0 1 0 1 (121.9 KiB) Viewed 26 times
- Complete The Table Only Required Is To Fill The Table I1 I2 I3 I4 Before Delay After Delay Q1 Q2 Q1 Q2 0 0 0 0 0 0 0 1 0 2 (100.65 KiB) Viewed 26 times
I1
I2
I3
I4
Before Delay
After Delay
Q1
Q2
Q1
Q2
0
0
0
0
0
0
0
1
0
0
1
0
0
0
1
1
0
1
0
0
0
1
0
1
0
1
1
0
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
1
0
1
1
1
1
0
0
1
1
0
1
1
1
1
0
1
1
1
1
PLC Automatic Door Control System • System have 2 motion detectors (11,12) O The door will open when one of the sensors detect motion. O • System have 2 outputs(Q1,Q2) One responsible for opening the door ,the other for closing door. And gates will be needed to build a standard interlocking circuit (B2,B3):by this way only one output can be active at time. . 2-detecors: 13:kimit switch open and 14 limit switch close: o the final position of the door are detected by the limit switches 13 and 14 (NC contact) 0 when the door is open 13 limit switch changes the state from close to open. o when the door is close 14 limit switch changes the state from close to open • we will add a off-delay block; when the detectors area of the 2 motion detectors is free for min time the door will close again. OBJECT DETECTIVE SENSOR DOOR OPEN DOOR OPEN OPEN LIMIT SWITCH CLOSE LIMIT SWITCH OPEN LIMIT SWITCH
Infrared sensor o Door Opening limit switch Closing limit sw Opening limit switch List of inputs/outputs List of inputs ·motion detectors: 11, 12 Closing limit switch: I. Opening limit switch: Iz List of outputs -Opening motor : Q Closing motor :- Q2 MDO 11 LSO 13 B001 R B002/2 B003 B004 Remont 10:00+ B002 MDI LSC 8001M