Question 1- Parta) Suppose that you have a network address (173.87.24.0/24) to subnet. Using the following topology, det
Posted: Sun Jul 03, 2022 11:22 am
Question 1- Parta) Suppose that you have a network address (173.87.24.0/24) to subnet. Using the following topology, determine the number of subnets needed and then design an appropriate addressing scheme. POP POLA Total Number of Subnets= New Subnet Mask Requirements- •RI LANs will require 3 IP addresses each •RI-A LAN will require 3 IP addresses • R1-B direct connection will require 2 IP addresses • The link between RI to RI-A will require an IP address for each end of the link • The link between R1 to R1-B will require an IP address for each end of the link • The link between RI-A to R1-B will require an IP address for each end of the link Subact Number 1 2 POLE 3 4 5 6 7 Saboot Address RI A 9 10 Fill in the following table with the subnet information- RI-A First Usable Host Addres Fill in the following table with IP addresses and subnet masks for the router, switch, and PC interfaces- Device Interface IP Address Sabot Mask Default Gateway F200 Fa SOOD RI-B SWI SW2 SORT Fa00 Last Usable Host Address SORT Fay Broadcast Address SOOD SORT VLANI VLANI
Subnet Number 1 2 3 4 for each end of the link 5 6 7 8 Subnet Address RI RI-A 9 10 Fill in the following table with the subnet information- RI-B First Usable Host Address Fill in the following table with IP addresses and subnet masks for the router, switch, and PC interfaces- Device Interface IP Address Subnet Mask Default Gateway SWI SW2 SWI-A PC PC2 PCI-A PCI-B Fate Fa0/1 50.00 in require all t 50/0/1 F200 50/0/0 50/0/1 F200 50/0/0 50/0/1 VLANI VLAN I VLAN I Last Usable Host Addres NIC NIC NIC NIC Breadcast Address Part b) Implement the topology on packet tracer and configure routing (Static/RIP) on all routers such that all PCs can communicate with each other Provide Screenshots for: . • Routing tables using CLI (before and after routing) o for all routers (2 screenshots - 1 before routing and 1 after routing, per router) o for example, if you have 4 routers, you need a total of 8 CLI screenshots Successful pings for all the hosts in the topology. (1 full screenshot)
Subnet Number 1 2 3 4 for each end of the link 5 6 7 8 Subnet Address RI RI-A 9 10 Fill in the following table with the subnet information- RI-B First Usable Host Address Fill in the following table with IP addresses and subnet masks for the router, switch, and PC interfaces- Device Interface IP Address Subnet Mask Default Gateway SWI SW2 SWI-A PC PC2 PCI-A PCI-B Fate Fa0/1 50.00 in require all t 50/0/1 F200 50/0/0 50/0/1 F200 50/0/0 50/0/1 VLANI VLAN I VLAN I Last Usable Host Addres NIC NIC NIC NIC Breadcast Address Part b) Implement the topology on packet tracer and configure routing (Static/RIP) on all routers such that all PCs can communicate with each other Provide Screenshots for: . • Routing tables using CLI (before and after routing) o for all routers (2 screenshots - 1 before routing and 1 after routing, per router) o for example, if you have 4 routers, you need a total of 8 CLI screenshots Successful pings for all the hosts in the topology. (1 full screenshot)