Answer Happy

• DRAWING VIEW Appearance Use scale of 1:1 and Shaded Style Orientation Front Style Scale 1:1 Edge Visibility Tangent Edges Interference Edges A-A (1:1) Thread Edges А Close 11 ID Example of section View of A-A side Tech ce Mohd Fairus Almed 14/22022 А final combine st 1/1 twiga 4
Assignment 1 Based on the lab tutorial topic 5.3, the circuit diagram named MK107 for LED running light was implemented in Fusion 360 with PCB design and 3D PCB model. Task 1. Change the size of the board to be 80 mm x 80 mm. Arrange all the electronic component and make sure all the LEDs are in one row. (10 marks) Task 2. Since the 3D model for the capacitor C1 (the 10 nF capacitor) does not has a 3D model, then you are required to model it. Design the capacitor 3D model by using “3D packages Generator” as shown in figure below. Choose suitable package according to any capacitor datasheet. Provide 1 page of the datasheet (in .pdf) together with your submission as a proof of the dimension. (10 marks) SOLID SURFACE MESH PCB PACKAGE SELECT FINISH Task 3. Since the 3D model for the potentiometer TRIM-EU-B25P does not has a 3D model, then you are required to model it. Replace the TRIM-EU-B25P package with TRIM EU-B64W by right click on the symbol and then choose Package. After changing the package, add the 3D model, by right click on the symbol and choose “Add custom 3D model”. Use the given 3D model of “3362W-1-203LF.stp" (20 marks) Task 4. Generate new 3D PCB based on the modification in Task 1 until Task 3. (5 marks) Task 5. Create drawing of the PCB for Front View, then from it, projected to Top view and to any 3d side view. Show any important dimensions. (5 marks) Submit your final 3D PCB design in the .f3z format (Click menu > Export > save in .f3-) to Google Classroom. Make sure you named your file as <YOUR FULLNAME_1>.f3z, otherwise you will be given a penalty on your mark. Submit datasheet for capacitor in the .pdf format to Google Classroom. Make sure you named your file as <YOUR FULLNAME_1>.pdf, otherwise you will be given a penalty on your mark. Combine your drawing from Task 5 into the same pdf file after the datasheet page.
1:40 OP + Bill 31%. Example of dra... E o Assignment AR Dura Based on the lab tutela 5, the cont degrund MK 17 for LED ring lightwa plemenice 360 with design and 3D model Task. Change the site of the board to be. Aminge de the destros component and make sure all the Low (10) Task 2 See the model for the capacitar Ch 10 of capace) des Dudel then you are required to model Design the capacitor medel by D pages Gership belowChoose the packaptaccording to any capacite datasheet Pavile of the destin dether with your satissa proof of the dicen (10 marks) SOLD SURFACE H PC UAE Tak Seth 3D model for the petition TRIM-EU-B25P Jos suos a 3D them you are required to see it Replace the TRIM-BU-32SP package with TRIM EL-364W tyhon the synthen choose Package. After dangthe package the 3D model by night click on the symbol ancho Add custom made use the given 3D modelf-1362W 1.303LF. (20mris Tukt. Geteste in D PC based on the medication in Tak Tun Tak 1. Stark Genc Tak Createdevis of the 18 foc Front View, then from , proto to Top view and to 1 side view. Show w portal 0000 HOM Tere AA(11) Sheet your litul DPC design in the Click mexport/Google Cle. Make sure you name your files YOUR FULLNAME>, wherwise you will be given a penalty on your mark Buwidtshot for capacitors the.pdf Google Make sure you are your NC Be YOUR PLINAME plethwise you will be show a penalty cayer. Combine your year drawing from Task Sinto the same perile after the datasheet page www Tal combine toaat