Answer Happy

Posted: **Wed Jun 08, 2022 8:50 am**

: Question 1 A 150 X 75 X 12 Angle Shown In Figure 1 Is Connected To A Gusset Plate Using A E70xx 10mm Weld Using S355jr 1 (25.2 KiB) Viewed 27 times

: Question 1 A 150 X 75 X 12 Angle Shown In Figure 1 Is Connected To A Gusset Plate Using A E70xx 10mm Weld Using S355jr 2 (63.56 KiB) Viewed 27 times

: Question 1 A 150 X 75 X 12 Angle Shown In Figure 1 Is Connected To A Gusset Plate Using A E70xx 10mm Weld Using S355jr 3 (31.38 KiB) Viewed 27 times

: Question 1 A 150 X 75 X 12 Angle Shown In Figure 1 Is Connected To A Gusset Plate Using A E70xx 10mm Weld Using S355jr 4 (29.31 KiB) Viewed 27 times

Question 1 A 150 x 75 x 12 angle shown in Figure 1 is connected to a gusset plate using a E70XX 10mm weld. Using S355JR steel do the following. 1.1 Calculate the design tensile resistance of the angle. (15) 1.2 If the transverse weld is removed calculate the tensile resistance that will govern the design. (5) Note: Check all possible failure modes 145mm 350mm 200 mm Figure 1: Gusset Plate Connection [20 Marks]

ABILIT Abok F N HANGE 02.....21-21 HTON ** AA 4 4 | 白菜菜菜第 Designto B xx 6 洗菜金、穀006 23 一 6 7 A 15x50x 4 1 4 4 4 75x50x6 80x65x6 SSD3601 Major Test 1 2022 經過 1 5555 09 do da 年 9 紫菜菜新路中金海珠宝 159 99 9.666 55 969式 5西湖西西南西部 ( 设箱分箱装箱晚安法克雅 995 93 96 紫菜包饭紫菜菜、紫菜、紫茄菜 656 日防線 662 666R 35 10 100 x 75 x 6 === 22 CCE 0X/X521 FEE 雞 150x75x10 OEXOXOST 10

Steel SSD3601 Major Test 1 2022 Table 2.1 MECHANICAL PROPERTIES FOR STEEL TO SANS 50025-2 Yeidshes, minimu for thickness ole Grade strength 1, ANS ENG Weap energy aborted MP An ww Am mm mm J 5235 300 10510 235 225 215 715 215 27 ionly specified 523530 360 510 235 225 215 215 215 27 52352 360 510 235 225 215 215 215 $275R 410 to 560 275 246 255 245 235 20 27 only if specified 275 265 255 245 235 0 27 $275J0 410 to 560 52752 410 560 275 265 255 245 235 -20 $355 470 to 630 355 345 305 315 20 27 only spected 535530 470 to 630 355 345 335 325 315 0 27 53552 470 o 630 355 345 335 325 315 -20 27 Notes: 1. Consult standards for thicknesses bigger than 100 mm 2. Minimum elongation in tensile test in order of 20% see standards 3. Charpy tests on S235JR, 52751 or S355JR only required if specified Dharpy nhing Tel temperature C 20 0 20 R

Telkom-Monate 08:12 Back SSD3601 Major Test... Table 2.1 MECHANICAL PROPERTIES FOR STEEL TO SANS 50025-2 G HAS SE w 523 12350 150 225 215 10 2 229 211 711 SUPER 340 25 $2750410540 275 410540 3470630 3047430 547060 Notes 1.Cilt standards for thickness bigger than 100 2. Minimum longation in tale est in under 20%-d 3. Charpy tests on 52, 273 or 5058 only quired if specified Steel zn 210 215 725 211 215 215 215 携徵 20 20 SSD3601 Major Test 1 2022 M wwerted ** 44% 4 RR-BRE BB